Unraveling the structure and role of Mn and Ce for NOx reduction in application

Nature Communications volume

Nature Communications volume 13, Article number: 2960 (2022) Cite this article

4949 Accesses

17 Citations

58 Altmetric

Metrics details

Mn-based oxides are promising for the selective catalytic reduction (SCR) of NOx with NH3 at temperatures below 200 °C. There is a general agreement that combining Mn with another metal oxide, such as CeOx improves catalytic activity. However, to date, there is an unsettling debate on the effect of Ce. To solve this, here we have systematically investigated a large number of catalysts. Our results show that, at low-temperature, the intrinsic SCR activity of the Mn active sites is not positively affected by Ce species in intimate contact. To confirm our findings, activities reported in literature were surface-area normalized and the analysis do not support an increase in activity by Ce addition. Therefore, we can unequivocally conclude that the beneficial effect of Ce is textural. Besides, addition of Ce suppresses second-step oxidation reactions and thus N2O formation by structurally diluting MnOx. Therefore, Ce is still an interesting catalyst additive.

The selective catalytic reduction (SCR) of environmentally harmful nitric oxide (NO) with ammonia (NH3) is a well-known and established technology for the denitrification of exhaust gases from stationary (power plant) and mobile (e.g., lean-burn engines) sources1,2,3. However, the more stringent global legislations and the relatively low exhaust temperatures of more efficient engines and low-load engine operations require the search for more efficient catalytic systems. For example, In Euro 6 stage, the European Union legislative authorities have tightened the limits of nitrogen oxides being emitted from diesel cars (from 180 mg NOx/km in Euro 5 to 80 mg NOx/km in Euro 6)4. A wide variety of catalytic systems based on metal-containing zeolites and mixed metal oxides have been investigated in this reaction. The introduction of Cu-exchanged small pore molecular sieves such as Cu-SSZ-13 and Cu-SAPO-34 have been a revolutionary technology for SCR applications5 and have an optimal performance between 200–450 °C6,7,8. Among mixed metal oxides, V2O5-WO3-/TiO2 catalysts give >90% NO conversion at gas hourly space velocities (GHSV) of 60000–90000 h−1 between 250–400 °C9,10,11,12,13. However, all these systems fall short of providing sufficient performance at temperatures below 200 °C. Catalysts operating at lower temperatures are imperative in mobile applications due to engine cold start14 and new advances in low-temperature combustion15. In this respect, manganese-containing mixed metal oxides exhibit excellent catalytic activity in the NH3-SCR reaction operating at temperatures below 200 °C, and therefore is of particular interest as a potential low-temperature component in NH3-SCR16,17,18,19,20,21,22,23.

Typically, Mn-based catalysts are prepared by impregnation or homogeneous precipitation methods with other metal oxides, such as Ti and Ce oxides, that act as support, dopants, or promoters. During the last decades, the role of the different components on the catalytic activity and selectivity have been debated extensively3. Mn catalytic activity originates from its excellent redox ability at low temperatures. The importance of specific surface area, dispersion, and oxidation state of the different Mn oxides have been highlighted24,25,26. TiO2 is considered a metal oxide support providing optimal dispersion of Mn active species, surface area, thermal stability, and Lewis acid sites to adsorb NH327,28. For Ce and other transition metal, there is no clear consensus on their role on the catalytic reaction. The promotional effect is often explained by an improvement of the catalytic redox cycles by intimate contact of the active Mn oxides and the promotors29,30,31,32. Among the transition metals, Ce is widely used and probably one of the most promising promotors3. In binary MnCe systems, the addition of Ce was reported to improve the conversion levels compared to individual Mn oxides33,34. This promotional effect is generally explained by an enhancement of the redox functionality, which is proven by the easier reduction of Ce and/or Mn during temperature-programmed reduction experiments35. Baiker et al. also postulated that binary MnCe oxides have a higher adsorption of NO and NH3, which promotes catalytic activity36. In ternary MnCeTi oxides, the improvement of activity by Ce is also frequently explained by an increase of the Mn redox properties35,37,38,39. In contrast, other studies suggest that the MnCe electronic interaction decrease the activity of Mn oxide species for NO conversion40 by a reduction of the Mn4+/Mn3+ ratio. On the basis of the measured surface areas, binary MnCe33,34,36 and tertiary MnCeTi35,37,40,41,42 systems show better textural properties when Ce is added, but this is rarely discussed as a main promoting effect.

To resolve this unsettled dilemma, we studied the structure and catalytic performance of Mn, Ce, and Ti mixed-oxide catalysts with a wide range of metal-oxide compositions. The catalysts were prepared by a homogeneous precipitation method designed to obtain mixed oxides with amorphous structure and a homogeneous dispersion of the distinct metal oxides. More specifically, 30 catalysts were systematically synthesized with different Mn, Ce, and Ti compositions. To verify the formation of an amorphous and homogeneous mixed oxide, we have chosen a multi-technique approach combining XRD, electron microscopy and high-resolution X-ray photoelectron spectroscopy. The low-temperature NH3-SCR performance of all the catalysts was investigated under relevant conditions encountered in a car exhaust (see experimental details).

After synthesis of the catalysts, we aim to characterize their structure and chemical properties by a multi-pronged approach. The crystalline structure of the catalysts was studied by powder X-ray diffraction, and crystallite sizes were calculated from diffraction peaks integral breadth using the Scherrer equation. The results are summarized in the ternary diagram plotted in Fig. 1 and the detailed diffraction patterns and crystallite size analysis are in the Supplementary information (Supplementary Fig. 2, Supplementary Fig. 3, and Supplementary Table S2).

Ternary phase diagram of the synthesized MnCeTiOx catalyst samples. The colored areas highlight groups of samples with similar crystal phases, measured by XRD.

The binary catalysts have a certain degree of crystallinity and show reflection lines of fluorite CeO2 structure in the CeTi and MnCe oxides and rutile TiO2 in the MnTi oxides. MnOx crystalline phases, α-Mn2O3 (Bixbyite), Mn5O8, Mn3O4 (Hausmannite), and MnO(OH) (Groutite) are observed on the MnCe oxides, whereas binary MnTi samples display weak and broad reflections from MnOx phases, indicating nano-crystallites below 3–4 nm, most likely on the TiO2 surface. The existence of mono-component metal oxide crystalline phases is an indisputable proof that the preparation method is not successful for the synthesis of well-mixed oxides in binary systems. In sheer contrast to the binary systems, the diffraction patterns of most of the ternary systems show featureless diffraction patterns indicating the amorphous nature of the samples (Supplementary Fig. 3). Only a few samples with high Ti (Mn0.08Ce0.13Ti0.79) or Ce (Mn0.07Ce0.55Ti0.37 and Mn0.11Ce0.48Ti0.41) content display reflections from anatase TiO2 or fluorite CeO2, respectively (see Supplementary Fig. 4). This suggest that the third metal component facilitates the formation of a ternary amorphous phase, which is the first step on obtaining a homogeneous mixed oxide. Very importantly, the effect of Ce is crucial in the formation of an amorphous phase, as small amounts of such a component inhibits the formation of crystalline phases, as can be observed in the low edge of the ternary diagram in Fig. 1.

The bulk and surface composition of the catalysts were compared by using Inductive Coupled Plasma (ICP) and high-resolution X-ray Photoelectron Spectroscopy (XPS), respectively (Supplementary Table S1). The bulk chemical composition of the catalysts is comparable with the theoretical composition, with a slight deviation to lower Mn concentrations, which suggests that not all the Mn is precipitated during synthesis. One plausible explanation is the formation of soluble Mn complexes with ammonium ligands, which are less prone to hydrolysis-condensation reactions43. Those are expected to remain in the supernatant during the washing by centrifugation, thus decreasing the final Mn content on the catalyst. The bulk composition was compared to the surface composition of selected samples by XPS. For the MnTi binary, there is an enrichment of Mn on the surface, in line with the hypothesis that Mn is supported on TiO2. For the ternary systems, the results show that surface compositions are similar to bulk compositions, with some of the samples displaying a modest enrichment of Mn and Ce on the surface.

To further investigate the structure, metal oxide distribution, and local composition of the catalysts, we performed a high-resolution electron microscopy study. A representative transmission electron microscopy (TEM) image of a binary MnTi Sample (Mn0.37Ce0.00Ti0.63) is shown in Supplementary Fig. 5. We observed nanosized and crystalline TiO2 particles decorated with layers of amorphous material. High-angle annular dark-field (HAADF) STEM imaging and elemental mappings computed from energy-dispersive X-ray spectroscopy (EDX) data, presented in Supplementary Fig. 6, reveal that Mn is well dispersed on the TiO2 particles. In contrast, TEM images of a representative MnCeTi ternary system, in Fig. 2a, b, corroborate the existence of a purely amorphous system. The structural features resemble an agglomeration of shapeless nanoparticles forming a random porous structure. Annular dark-field (ADF) STEM imaging and elemental mapping computed from EELS data confirm the homogeneous distribution of Mn, Ce, and Ti metals over individual catalyst particles.

a, b Representative HRTEM images of the Mn0.14Ce0.13Ti0.74 oxide catalyst. ADF-STEM images and elemental mappings of the same catalyst at (c–g) low and (h–l) high magnification.

All the results strongly confirm that our synthesis route renders a homogeneous distribution of all the metal atoms in the ternary system and indicate that our synthesis method is effective for the preparation of ideal perfectly-mixed ternary metal oxides. From the characterization measurements conducted, we illustrate the structure of the MnTi binary and the MnCeTi ternary catalysts in Fig. 3.

a MnTi binary catalysts where amorphous layers of Mn oxide active are on the surface of crystalline TiO2 and b MnCeTi ternary catalysts where the metal oxides are amorphous and well mixed.

The specific surface areas of the discrete catalysts are presented in the ternary diagram in Fig. 4 and in Supplementary Fig. 7 and Supplementary Table S3.

Ternary diagrams showing the Influence of catalyst composition on BET surface area.

The catalyst materials have a clear type IV isotherm, with an H2 or H3 loop characteristic of mesoporous coming from the agglomeration of the metal-oxide nanoparticles44. Clearly, Ce content has a significant impact on specific surface areas of the ternary catalysts. The addition of Ce plays a key role as structural promotor increasing the surface area from 108 to 245 m2/g when Ce content increases from 0 to 20 mol%. A further increase in Ce has a negative impact and surface areas drop down to 62 m2/g when Ce concentration reaches 55 mol%, similar to previous studies on CeTi45, MnCe46 binary systems and MnCeTi ternary systems47. Comparing the XRD and BET data, the increase of surface area is strongly correlated with the formation of amorphous structures.

To investigate the redox properties of the materials, temperature-programmed reduction (TPR) experiments with H2 were performed. Overall, the reduction peak at 200–450 °C is attributed to the reduction of Mn4+ and Mn3+ species to Mn2+ 48,49, whereas the main reduction peak at 550–650 °C is ascribed to the reduction of Ce4+ to Ce3+ in a mixed oxide phase50,51,52. The difference in the TPR of pure CeO2, plotted on supplementary Fig. 8, confirms that Ce is well-mixed and strongly interacting with Mn and Ti. The samples containing a low Mn/Ce molar ratio, plotted in Fig. 5a, show a monotonic decrease in the reduction temperature of Ce when Mn content increases. According to literature reports, the main parameters influencing the reduction temperature are specific surface area and the presence of other metals in intimate contact53. In this case, the surface area of the binary Ce-Ti system is higher than the Mn-contained samples shown in Fig. 5a. Therefore, changes in the reduction temperature are unrelated to specific surface area and can be rationalized as a consequence of the close proximity of Mn and Ce species, which improves the reducibility and thus the redox properties of Ce. The TPR of samples containing high amount of Mn are shown in Fig. 5b. For the binary MnTi samples, two main peaks from Mn reduction (289–306 °C and 341–408 °C) are observed. Addition of Ce in the catalyst formulation has a strong impact on the TPR profiles: the low-temperature peak strongly decreases with small amounts of Ce and the high-temperature contribution shifts to higher temperatures with increasing Ce content (see also Supplementary Fig. 9). We surmise that the changes in the TPR profiles probably result from the lower reducibility of the Mn species in close contact with Ce.

Temperature-programmed reductions with H2 of selected samples with (a) a low Mn/Ce molar ratio and (b) a high Mn/Ce molar ratio. The low-temperature evolution (in purple) is related to the reduction of MnOx phases whereas the high-temperature (in cream) is related to CeO2 reduction. Mn K-edge (c) XANES, (d) EXAFS, and (e) FT-EXAFS spectra of three selected catalyst compositions, Mn0.35Ce0.00Ti0.65, Mn0.37Ce 0.04Ti0.60, Mn0.30Ce0.19Ti0.51.

To gain more nuanced insight into the effect of Ce to the catalyst properties, a detailed high-resolution XPS study was performed. Oxidation states of Mn were rigorously fitted from a set of Gaussian-Lorentzian components per oxidation state, due to the multiplet splitting between the unpaired electrons in Mn 2+, 3+, and 4+. The set of components of the discrete oxidation states were obtained from measurements of pure MnO, Mn2O3, and MnO2 oxides and the results were compared with previously reported measurements54. More experimental details can be found in the supplementary information and Supplementary Fig. 10. The Mn (2p3/2) spectra from selected samples show a high amount of Mn3+ species in the binary MnTi catalysts, whereas a combination of Mn4+ and Mn2+ dominates the spectra of ternary samples (see Supplementary Table S5). There is no clear consensus in the literature on the effect of Ce on the Mn oxidation state. Whilst several authors found an increase in Mn3+ species with the addition of Ce35,39,40, Feng et al. observed a slight reduction in Mn3+ 42, and others found no clear correlation55,56. The origin of the discrepancy could be related to the complexity on the analysis of the Mn (2p3/2) spectra and the different structure of the prepared catalysts. In order to improve the confidence in our results, average Mn oxidation states were calculated from the XPS and TPR and gave comparable results (see Supplementary Table 7), which validates our XPS deconvolution method and confirms that the addition of Ce decreases the average Mn oxidation state. Raman spectra of selected binary MnTi and ternary MnCeTi were also collected and qualitative analysis is in line with the XPS and H2-TPR results (see supplementary information, Supplementary Fig. 11 and Supplementary Table S6). Based on our structural characterization results, we speculate that the reduction in the average Mn oxidation state is due to the existence of Ce species in close proximity to Mn. This might explain the shifting of TPR profile to high temperature after introducing Ce into the MnTi system.

Additional information about the chemistry and structure of Mn on selected samples was obtained by X-ray absorption spectroscopy (XAS). Mn K-edge spectra were recorded ex situ for selected binary (Mn0.35Ce0.00Ti0.65) and ternary (Mn0.37Ce0.04Ti0.60 and Mn0.30Ce0.19Ti0.51) samples to investigate the effect of Ce in the Mn oxidation state and local structure. All XANES spectra (Fig. 5c) display a weak peak in the pre-edge region (inset) due to the 1 s → 3d quadrupolar transitions and a white line characteristic of an oxidized state of Mn sitting mostly in octahedral environments57,58. Depending of the Ce concentration, the position of the 1 s → 3d transitions are located at different energies indicating different manganese oxidation states. Without Ce, Mn is found in its most oxidized state (1 s → 3d: 6542.0 eV), while adding Ce reduces the average Mn oxidation state. The same findings are observed regarding the absorption edge energies at 6551.6, 6549.2, 6550.0 eV respectively for Mn0.35Ce0.00Ti0.65, Mn0.37Ce0.04Ti0.60 and Mn0.30Ce0.19Ti0.51 compositions. An estimate of the average Mn oxidation state was performed by comparison with manganese oxide standards. More details about the analysis can be found in the supplementary information. Summarizing, the average oxidation states (in Supplementary Table S7) are in agreement with the XPS and H2-TPR data.

Subsequent qualitative assessment of the EXAFS spectra in Fig. 5d, e shows a main peak at about 1.42 Å attributed to Mn-O scattering paths and several peaks between 2.0 and 5 Å assigned mainly to Mn-Mn paths with some minor contributions from Mn-O scattering and some multiple scattering processes. The peak area corresponding to the Mn-Mn scattering paths are larger for the binary Mn0.35Ce0.00Ti0.65 indicating that the later materials has the best long-range order among the three composition (while still appearing amorphous by XRD). The ternary samples display the strongest disorder, supporting than such a system is a homogeneous mixture of mixed oxides.

Next, we inspected the activity of the different samples in the selective catalytic reduction of NO with NH3 at 150 °C. During the activity measurements, there was no NO2 formation, and the only products were N2 and N2O. Activity plot with the amount of Mn shows a close-to-zero intercept of the ordinate, indicating that Mn oxides are the most important species in catalytic performance (Supplementary Fig. 13). Up to 60% of Mn, there is a modest correlation of the increase of activity with the increase in Mn content. However, the results revealed that no evident trend is observed when Mn is above 60% and strongly suggest that Mn content is not the only factor determining catalytic activity.

To unravel the effect of the distinct metal oxides, we re-examined the catalytic performance by surface area normalization of the activity. Specific activities (ml of NO converted per m2 and per min) were plotted as a function of Mn content in Fig. 6. For the individual Mn and the binary MnTi samples, a clear linear dependency of the measured specific activities with the Mn content is observed. The MnCeTi ternary systems has also a pseudolinear correlation with the Mn content but with a lower slope. The Mn surface enrichment for the MnTi catalysts observed by XPS (Supplementary Table S1) can insufficiently explain the almost twofold increase in specific activity. Therefore, we infer that MnOx species in the individual Mn and binary MnTi catalysts have similar activity, and those are more active than in the MnCeTi ternary system. The results are also in line with the higher reduction temperature of manganese species observed in the TPR data of MnCeTi ternary systems.

Surface-specific activities for the NO reduction at 150 °C plotted as a function of the Mn content on the catalysts. The blue dots correspond to the ternary MnCeTi catalysts. The red dots are from the binary MnTi and the individual Mn catalysts. Red and blue trendlines were added to guide the eyes.

To assess the implication of the different MnOx species on catalytic performance, the normalized activities with the distinct Mn surface species (Mn4+, Mn3+, Mn2+, and total Mn) were constructed in Supplementary Fig. 14. The plots show an increase in activity with the amount of Mn4+ and Mn3+ species, however there are no direct evidences that the Mn2+ species are promoting catalyst activity, in line with previous reports59. Hence, the increase in the Mn2+ content in the samples containing Ce could, to a certain extent, explain the lower specific activity of those samples. In addition, the substantial effect of Ce on the TPR profiles, shifting reduction peaks of Mn4+ and Mn3+ to higher temperatures, indicates that other interactions of Mn4+ and Mn3+ with Ce species can be responsible for the lower specific activity.

We further investigated the nature of the oxygen species in the solid catalyst, which has been suggested to have a significant impact on SCR activity, more specifically on the oxidation reactions60,61. The reactivity of oxygen species on the catalyst was investigated by monitoring the formation of N2O during NH3-TPD experiments. In these experiments, N2O is formed in the range of 140–40 °C via the oxidation of ammonia with active oxygen species on the catalyst surface. The plots in supplementary Fig. 15. shows that NO activities at 150 °C are correlated to the amount of N2O evolved during the NH3-TPD experiments, which points to the direct role of the active oxygen in the overall reaction mechanism at low temperature. Since the NO activity is related to Mn content, we can infer that those active oxygen species are related to Mn species.

The effect of the adsorption of NO and NO + O2 on catalytic performance was also investigated by temperature-programmed techniques in selected samples with similar Mn content (Supplementary Fig. 16). Quantification during NO experiments shows a higher adsorption of NO for the binary MnTi sample. In the case of the NO + O2 adsorption measurements, the sample with a small amount of Ce has a larger amount of NO adsorbed. The lack of a clear trend evidences that the capacity of NO and NO + O2 adsorption is unable to fully describe the catalytic performance.

The effect of Ce on the Mn activity has been previously reported in the literature with inconsistent findings. For example, Liu et al. proposed a positive effect of Ce and Ti in activity by a dual redox cycle consisting of Mn4+ + Ce3+ ↔ Mn3+ + Ce4+ and Mn4+ + Ti3+ ↔ Mn3+ + Ti4+ cycles35. A different explanation of the beneficial effect of Ce was proposed by Yang et al., based on a mechanistic study using in-situ FTIR spectroscopy. The authors suggested that MnOx species show a faster rate for the conversion of NO to nitrate or nitrite, whereas CeO2 mainly provides adsorption sites resulting in nitrites species33. In line with our results, Wu et al. also observed a negative effect of Ce in the activity in ternary MnCeTi compared to binary MnTi. However, these authors explained the negative effect of Ce by a reduction in the Mn4+/Mn3+ ratio40. In order to resolve the origin of these contradicting findings, our results were contrasted with previously reported ones after surface-area normalization of the activity data. These data are shown in Supplementary Table S11. The analysis shows that when the activities are surface-area normalized, there is no positive effect of the addition of Ce on the specific Mn activity, which validates our experimental results. Although this analysis is incomplete due to our lack of knowledge on several parameters, such as Mn surface composition, oxidation states, degree of interaction between the different oxide species, etc., there is no apparent trend pointing to an increase in activity by Ce addition. Therefore, we propose that Ce is not improving the intrinsic catalytic properties of Mn species at low reaction temperatures and that the only promotional effect of Ce is purely structural due to an increase in catalyst surface area.

When looking at the catalytic performance at higher temperatures, the role of Ce is clear. Supplementary Fig. 17 shows NOx conversion of selected samples with increasing the amount of Ce. The activity data of all catalyst samples can be found in Supplementary Table S8. The binary MnTi catalysts has the highest activity at low temperatures, but the catalytic performance drastically drops at temperatures >250 °C due to the unselective oxidation of NH3 to NOx. The addition of Ce drops the conversion at low temperatures, but promotes NOx conversion at temperatures >250 °C, widening the operational temperature window of the catalyst materials. Understanding this effect lies beyond the scope of our investigations as other parameters, such as close proximity of the redox and acidic functions, may govern the reaction at high temperatures62.

Finally, the N2O formation at low temperature was investigated on all the samples. Possible effects of conversion on N2O selectivity were ruled out by inspecting the N2O selectivity plot as function of conversion in Supplementary Fig. 18. In general, the N2O formed over MnOx and binary MnTi catalysts is significantly higher than in the MnCeTi ternary systems. For a deeper analysis of the selectivity results, the surface-specific formation of N2O of selected samples was plotted in Fig. 7 as function of the Mn surface density calculated from the XPS measurements. The results clearly show an exponential increase of the N2O formation at 150 °C with the Mn surface density, indicating that N2O formation obeys a higher-than-one-order dependence in Mn. Our characterization and NOx activity measurements pointed to an interaction of Ce with Mn, leading to a decrease in the Mn activity. This can definitely play a role in the lower N2O activity but does not fully describe the Mn order dependence. A plausible explanation of this behavior is that more than one Mn active species in close proximity must participate in the kinetic formation of N2O. According to literature, two main reaction mechanisms explain the formation of N2O at low temperature63: one base on a Langmuir-Hinshelwood mechanism where NO is oxidized to NO3− species that react with NH4+ to give N2O, and the other is an Eley-Rideal mechanism resulting from the oxidative dehydrogenation of NH3 to NH species that react with NO to yield N2O. A mechanistic study on the formation of N2O is beyond the goal of this work, but both proposed mechanisms are based on multistep oxidation of NO and/or NH3. Therefore, we postulate that the formation of N2O requires the participation of at least two Mn active sites and that is promoted by neighboring Mn active sites. The homogeneous composition of the ternary MnCeTi dilutes the Mn species on the catalyst surface and inhibits subsequent oxidation steps by breaking up the MnOx ensembles. This mechanism is schematically depicted in Fig. 8. Besides the dilution effect, the addition of Ce could also decrease the activity of surface oxygen observed by a suppressed N2O formation in the NH3-TPD.

Surface-specific N2O rates at 150 °C as a function of the Mn surface density. Samples from lower to higher Mn surface density: Mn0.08Ce0.55Ti0.37, Mn0.14Ce0.13Ti0.74, Mn0.21Ce0.25Ti0.54, Mn0.30Ce0.19Ti0.51, Mn0.36Ce0.04Ti0.60, Mn0.35Ce0.00Ti0.65. The blue line is a guide to the eye suggesting an exponential-type trend.

a MnTi binary catalyst where the close proximity of MnOx species promotes the formation of N2O and b MnCeTi ternary catalyst in which the well-mixed amorphous structure promotes the spacing of MnOx species and therefore reduces the formation of N2O. For the gas molecules: red is oxygen, blue is nitrogen, and white is hydrogen.

To rule out the effect of the amount of ammonia adsorbed on the catalysts on N2O selectivity, NH3-TPD measurements were performed and the total number of acid sites, obtained from the total amount of ammonia adsorbed, was plotted as a function of Ce content (Supplementary Fig. 19). The total acidity of all the samples was also plotted in the ternary diagram in Supplementary Fig. 20. The total acidity is around 1.1 μmol/m2 up to 20% Ce and then monotonically increases up to around 2.5 μmol/m2. Owing to the fact that the inhibiting of N2O formation is observed in catalysts with Ce content below 20%, we can exclude the role of the number of acid sites on the N2O formation.

Concluding, our research results add new insight into our understanding of Mn catalysts for low-temperature NH3-SCR applications and provides a direction toward settling the ongoing debate over the effect of Ce on the Mn active species. We postulate that the activity of the Mn active sites is not positively affected by Ce species in intimate contact. In fact, our results suggest that Ce is decreasing the average oxidation state and activity of Mn active species and is just a structural promotor, increasing catalyst surface area. On the other hand, addition of Ce is increasing N2 selectivity as it suppresses second step oxidation and thus N2O formation by a dilution effect on the MnOx active sites. The latter still makes Ce an attractive additive for MnTi systems.

Titanium(IV) sulfate solution (Ti(SO4)2, Pfaltz & Bauer., 30% in H2SO4), cerium(III) nitrate hexahydrate (Ce(NO3)3·6H2O, Sigma-Aldrich, 99.999% trace metals basis), manganese(II) nitrate hydrate (Mn(NO3)2·xH2O, Sigma-Aldrich, 99.999% trace metals basis), ammonium hydroxide (NH4OH, Alfa Aesar, ACS grade, 28.0–30.0%) were used as received, without further purification.

A series of individual, binary and ternary materials with different molar concentrations were prepared by a controlled co-precipitation method as described in the Supplementary information and Supplementary Fig. 1. Our method is a novel and highly efficient approach, where the aim is to precipitate all metals at the same pH level to obtain a homogeneously well-mixed metal oxide system. This is done by dual dosing of NH3 and salt solution at a constant predetermined volumetric ratio. In most literature, the salt solution is added dropwise to an NH3 solution, but this gives a pH change over time (from high to final low pH) and could lead to a suboptimal co-precipitation of the elements. First manganese nitrate hydrate (Mn(NO3)2·xH2O), and cerium nitrate (Ce(NO3)3.6H2O) were dissolved in deionized water and stirred for 10 min. Then, a 30% titanium sulfate solution [Ti(SO4)2 in H2SO4] was added to the salt solution. These solutions were mixed under magnetic stirring at a constant speed (400 rpm) for 30 min, leading to a perfectly mixed metal salt solution. The mixed metal salt solution (loaded in a syringe pump) was injected simultaneously along with 14.7 M solution of ammonium hydroxide with a Gilson pump (NH4OH, Sigma-Aldrich, 97%) to a recipient containing 20 ml of mother solution that is already at the target pH of 10.5. During this simultaneous injection of the metal precursor and base, the resulting suspension was continuously stirred. This procedure allows to operate at a constant pH of around 10.5 by adding the same amount of hydroxide consumed during the catalyst precipitation reaction. The metal oxides will precipitate at the same time, rendering a very high level of homogeneity. Then, the precipitated solution was stirred for 30 min at 400 rpm. The sample was centrifuged at 7500 x g and washed several times with milli-Q water until the conductivity of the supernatant reached to 50 μs.cm−1. Then the samples were dried overnight at 100 °C, followed by calcination at 500 °C for 6 h. The list of samples and compositions is shown in Supplementary Table S1.

X-ray diffraction patterns were obtained using a Bruker D8 Advanced A25 diffractometer in Bragg-Brentano geometry with Cu Kα, β radiation source operated at 40 kV and 40 mA. β radiation is filtered out with a Ni plate. The diffractograms were measured with step size of 0.05° in the 2θ range of 10–80°. Nitrogen adsorption and desorption isotherms of the samples were measured at 77 K using Micromeritics ASAP-2420 surface area and porosity analyzer instrument. Samples were previously evacuated at 300 °C for 3 h. Specific surface areas and pore size distribution were calculated according to multi-point Brunauer–Emmett–Teller (BET) and Barret–Joyner–Halenda (BJH) method, respectively. From the adsorption data, total pore volumes were estimated at P/P0 = 0.99. The elemental compositions (Mn, Ce, Ti) of the samples were determined by an inductively coupled plasma spectrometer (Model 8900, Agilent Technologies). The samples were dissolved in HF and HCl. High-resolution Kratos Axis Ultra X-ray photoelectron spectroscopy equipped with a monochromatic Al Kα source was used to determine the surface composition and chemical states of the samples. All analyses were monitored using the C 1 s signal for adventitious carbon (284.8 eV). The chemical states of manganese in the catalysts were determined by peak modeling in CasaXPS software. To model the Mn 2p3/2 peaks of the catalysts, pure MnO, Mn2O3, and MnO2 samples were used as reference. Manganese(IV) oxide (99.997% - metals basis) was acquired from Alfa Aesar (Fisher US), manganese(III) oxide (99.9% - trace metals basis) was acquired from Sigma Aldrich, and manganese(II) oxide (99.99% - trace metal basis) was acquired from Acros Organics (VWR). The fitting parameters data (FWHM and Peak positions) obtained from the peak modeling of the standard samples were used for the calculation of the chemical state of manganese in our catalysts. H2-TPR experiments were performed in Autochem 2950 instrument equipped with a thermal conductivity detector. All catalysts (100 mg) were pretreated in a U-shaped quartz tubular micro-reactor in a flow of Ar at 250 °C for 2 h to yield a clean surface and then cooled down to 40 °C. Then, the temperature was raised from 40 to 1000 °C at a rate of 10 K/min under a flow of 10 vol.% H2 (90 vol.% Ar). The acidity of samples was determined by temperature-programmed desorption of ammonia (NH3-TPD). NH3-TPD of samples was performed in a fixed bed quartz tube reactor. Prior to the measurement, the samples were first pretreated at 500 °C under N2 flow. The reactor was cool down at 100 °C and samples were saturated with 1050 ppm NH3 for 30 min. The samples were flush with N2 for 30 min at room temperature, and then the temperature was increased to 500 °C at a rate of 10 K/min. The outlet gas composition (NH3, NO, NO2, N2O) was monitored by using a MultiGas™ 2030 FTIR Continuous Gas Analyzer. High-resolution transmission electron microscopy (HRTEM) micrographs obtained from a Titan 60–300 TEM (FEI Co, Netherlands) equipped with an electron emission gun operating at 200 kV. The annular Dark-Field scanning transmission electron microscopy (ADF-STEM) in conjunction with electron energy loss spectroscopy (EELS) study was carried out with a Cs-Probe Corrected Titan microscope (Thermo-Fisher Scientific) which was also equipped with a GIF Quantum of model 966 from Gatan Inc. (Pleasanton, CA). STEM-EELS analysis was performed by operating the microscope at the accelerating voltage of 300 kV, using a convergence angle α of 17 mrad and a collection angle β of 38 mrad. Spectrum-imaging dataset includes the simultaneous acquisition of zero-loss and core-loss spectra (DualEELS) using a dispersion of 0.5 eV/channel and were recorded using a beam current of 0.2 nA and a dwell time of 50 ms/pixel. The Ti L2,3-edge, Mn L2,3-edge, and Ce M4,5-edge were selected to build the chemical maps. X-ray absorption spectroscopy (XAS) was performed on the CRG-FAME beamline (BM30B), at the European Synchrotron Radiation Facility in Grenoble. Samples were all diluted with boron nitride (BN) and compressed into a 5 mm diameter pellet to allow the measurement in transmission mode. For all compounds the dilution level corresponded to the optimal sample thickness for transmission experiments (edge jump close to 1). The spectrum of metallic iron was measured with a metallic foil and was also used to perform the energy calibration of the monochromator (pseudochannel-cut/Si (220), energy resolution 0.335 eV). All XAS data were processed using the FASTOCH package. The XANES and EXAFS spectra were obtained after performing standard procedures for pre-edge subtraction, normalization, polynomial removal, and wavevector conversion. The NO and NO + O2 adsorption experiments were conducted in a fixed bed quartz tube reactor loaded with 100 mg of sample (PID Eng&Tech). Before loading, the catalysts were pressed in pellets, crushed and sieved to yield particles with a size between 500 and 710 μm. The NOx concentration (ppm) was measured with a Signal Model 4000VM NOx Analyzer (signal instrument). The samples were pretreated in a flow of 12.5% O2/N2 (800 mL min−1) with a heating ramp of 30 °C min−1 until 500 °C for 45 min and then cooled down to 100 °C, followed by 20 min isothermal period in N2 atmosphere (700 mL min−1). Afterward, the samples were exposed to a flow of 550 ppm NO or NO + 5% O2 in N2 (200 mL min−1) for 40 min, and then purged for 2 h with a N2 flow of 100 mL min−1. Finally, for the TPD portion, the temperature was increased from 100 to 500 °C at a rate of 10 °C min−1 in a N2 atmosphere (100 mL min−1).

The catalytic activity measurements of the catalysts in the NH3-SCR reaction were carried out in a fixed bed quartz tube reactor loaded with 0.5 ml of sample (PID Eng&Tech). Before loading, the catalysts were pressed into pellets, crushed and sieved to obtain a fraction between 500 and 710 µm. Application-relevant catalyst particle size, space velocity, and gas composition were applied. The inlet NOx composition was set on pure NO to avoid higher conversions coming from the "fast SCR" mechanism when NO2 is present. The total flow was maintained at 1000 ml/min, and the reaction condition corresponds to GHSV of 120,000 hr−1. The flow rate of gases was controlled using Bronkhorst mass flow controllers. A Controlled Evaporation and Mixing system (CEM) from Bronkhorst was used for evaporation of the required H2O in the gas feed before entering the reactor. The inlet gas stream contained 450 ppm NO, 500 ppm NH3, 5% O2, 5% H2O, and N2 balance. A MultiGas™ 2030 FTIR Continuous Gas Analyzer was used to analyze the inlet and outlet gas compositions (NO, NO2, NH3, N2O). The catalytic tests were performed in the temperature range of 150–500 °C (with an interval of 50 °C) at ambient pressure. NO conversion and N2O selectivities were calculated under steady-state conditions. The SCR activity (NO conversion) and N2O selectivity are calculated as follows:

Where [NH3]in, [NOx]in, [NH3]out, [NOx]out, and [N2O]out were the concentrations of NH3 and NOx(including NO and NO2) at the inlet and those at the outlet.

Surface-specific activities were calculated by normalization of the activities by the specific surface area obtained from the N2 physisorption isotherms (BET method).

The data supporting the findings of this article are available in the paper and in the Supplementary Information. Additional data are available from the corresponding author on reasonable request.

Sorrels, J. L. Selective Catalytic Reduction. U.S. Enviromental Protection Agency. https://www.epa.gov/economic-and-cost-analysis-air-pollution-regulations/chapter-2-selective-catalytic-reduction (2019).

Zhang, R., Liu, N., Lei, Z. & Chen, B. Selective transformation of various nitrogen-containing exhaust gases toward N2 over zeolite catalysts. Chem. Rev. 116, 3658–3721 (2016).

Article CAS PubMed Google Scholar

Han, L. et al. Selective catalytic reduction of NOx with NH3 by using novel catalysts: state of the art and future prospects. Chem. Rev. 119, 10916–10976 (2019).

Article CAS PubMed Google Scholar

Johnson, T. V. Diesel emission control in review. SAE Int. J. Fuels. Lubr. 1, 68–81 (2009).

Article CAS Google Scholar

Bull, I. X. et al. Copper CHA zeolite catalyst. US patent US7601662B2 (2009).

Fickel, D. W. & Lobo, R. F. Copper coordination in Cu-SSZ-13 and Cu-SSZ-16 investigated by variable-temperature XRD. J. Phys. Chem. C. 114, 1633–1640 (2010).

Article CAS Google Scholar

Girard, J., Cavataio, G., Snow, R. & Lambert, C. Combined Fe-Cu SCR systems with optimized ammonia to NOx ratio for diesel NOx control. SAE Int. J. Fuels. Lubr. 1, 603–610 (2009).

Article CAS Google Scholar

Kwak, J. H., Tonkyn, R. G., Kim, D. H., Szanyi, J. & Peden, C. H. Excellent activity and selectivity of Cu-SSZ-13 in the selective catalytic reduction of NOx with NH3. J. Catal. 275, 187–190 (2010).

Article CAS Google Scholar

Chen, J. & Yang, R. Role of WO3 in mixed V2O5-WO3/TiO2catalysts for selective catalytic reduction of nitric oxide with ammonia. Appl. Catal. A: Gen. 80, 135–148 (1992).

Article CAS Google Scholar

Xu, T. et al. Comparative study on sulfur poisoning of V2O5-Sb2O3/TiO2 and V2O5-WO3/TiO2 monolithic catalysts for low-temperature NH3-SCR. Catal. Commun. 93, 33–36 (2017).

Article CAS Google Scholar

Tian, X., Xiao, Y., Zhou, P., Zhang, W. & Luo, X. Investigation on performance of V2O5–WO3–TiO2–cordierite catalyst modified with Cu, Mn and Ce for urea-SCR of NO. Mater. Res. Innov. 18, S2-202–S202-206 (2014).

Article CAS Google Scholar

Lian, Z., Li, Y., Shan, W. & He, H. Recent progress on improving low-temperature activity of Vanadia-based catalysts for the selective catalytic reduction of NOx with ammonia. Catalysts 10, 1421 (2020).

Article CAS Google Scholar

Narkhede, V., Kumar, D., Cursetji, R. M. & Sidiquie, T. A. Low Temperature Selective Catalytic Reduction of NOx over Vanadium-Based Catalysts (SAE International, 2015).

European Commission. Including Cold-Start Emissions in the Real-Driving Emissions (RDE) Test Procedure: An Assessment of Cold-Start Frequencies and Emission Effects. (Publications Office, 2017).

Chatterjee, S., Naseri, M. & Li, J. Cleaning Interval Selection for SCR Considering Endurance Reliability and Emissions Reduction Efficiency in Heavy Duty Commercial Engine (SAE International, 2017).

Singoredjo, L., Korver, R., Kapteijn, F. & Moulijn, J. Alumina supported manganese oxides for the low-temperature selective catalytic reduction of nitric oxide with ammonia. Appl. Catal. B Environ. 1, 297–316 (1992).

Article CAS Google Scholar

Jin, R. et al. The role of cerium in the improved SO2 tolerance for NO reduction with NH3 over Mn-Ce/TiO2 catalyst at low temperature. Appl. Catal. B Environ. 148, 582–588 (2014).

Article CAS Google Scholar

Pappas, D. K., Boningari, T., Boolchand, P. & Smirniotis, P. G. Novel manganese oxide confined interweaved titania nanotubes for the low-temperature Selective Catalytic Reduction (SCR) of NOx by NH3. J. Catal. 334, 1–13 (2016).

Article CAS Google Scholar

Thirupathi, B. & Smirniotis, P. G. Nickel-doped Mn/TiO2 as an efficient catalyst for the low-temperature SCR of NO with NH3: Catalytic evaluation and characterizations. J. Catal. 288, 74–83 (2012).

Article CAS Google Scholar

Xiong, Y. et al. Effect of metal ions doping (M = Ti4+, Sn4+) on the catalytic performance of MnOx/CeO2 catalyst for low temperature selective catalytic reduction of NO with NH3. Appl. Catal. A: Gen. 495, 206–216 (2015).

Article CAS Google Scholar

Damma, D., Pappas, D. K., Boningari, T. & Smirniotis, P. G. Study of Ce, Sb, and Y exchanged titania nanotubes and superior catalytic performance for the selective catalytic reduction of NOx. Appl. Catal. B Environ. 287, 119939 (2021).

Article CAS Google Scholar

Li, J. et al. Effect of aluminum on the catalytic performance and reaction mechanism of Mn/MCM-41 for NH3-SCR reaction. Appl. Surf. Sci. 534, 147592 (2020).

Article CAS Google Scholar

Liu, X. et al. The promoting effect of S-doping on the NH3-SCR performance of MnOx/TiO2 catalyst. Appl. Surf. Sci. 508, 144694 (2020).

Article CAS Google Scholar

Tang, X., Hao, J., Xu, W. & Li, J. Low temperature selective catalytic reduction of NOx with NH3 over amorphous MnOx catalysts prepared by three methods. Catal. Commun. 8, 329–334 (2007).

Article ADS CAS Google Scholar

Kang, M., Yeon, T. H., Park, E. D., Yie, J. E. & Kim, J. M. Novel MnOxCatalysts for NO reduction at low temperature with ammonia. Catal. Lett. 106, 77–80 (2006).

Article CAS Google Scholar

Kang, M., Park, E. D., Kim, J. M. & Yie, J. E. Manganese oxide catalysts for NOx reduction with NH3 at low temperatures. Appl. Catal. A: Gen. 327, 261–269 (2007).

Article CAS Google Scholar

Smirniotis, P. G., Sreekanth, P. M., Pena, D. A. & Jenkins, R. G. Manganese oxide catalysts supported on TiO2, Al2O3, and SiO2: a comparison for low-temperature SCR of NO with NH3. Ind. Eng. Chem. Res. 45, 6436–6443 (2006).

Article CAS Google Scholar

Ettireddy, P. R., Ettireddy, N., Mamedov, S., Boolchand, P. & Smirniotis, P. G. Surface characterization studies of TiO2 supported manganese oxide catalysts for low temperature SCR of NO with NH3. Appl. Catal. B Environ. 76, 123–134 (2007).

Article CAS Google Scholar

Wan, Y. et al. Ni-Mn bi-metal oxide catalysts for the low temperature SCR removal of NO with NH3. Appl. Catal. B Environ. 148-149, 114–122 (2014).

Article CAS Google Scholar

Chen, Z. et al. Low-temperature selective catalytic reduction of NOx with NH3 over Fe–Mn mixed-oxide catalysts containing Fe3Mn3O8 phase. Ind. Eng. Chem. Res. 51, 202–212 (2012).

Article CAS Google Scholar

Liu, Z., Liu, Y., Li, Y., Su, H. & Ma, L. WO3 promoted Mn–Zr mixed oxide catalyst for the selective catalytic reduction of NOx with NH3. Chem. Eng. J. 283, 1044–1050 (2016).

Article CAS Google Scholar

Kang, H. et al. Solvent-free elaboration of Ni-doped MnOx catalysts with high performance for NH3-SCR in low and medium temperature zones. Mol. Catal. 501, 111376 (2021).

Article CAS Google Scholar

Qi, G., Yang, R. T. & Chang, R. MnOx-CeO2 mixed oxides prepared by co-precipitation for selective catalytic reduction of NO with NH3 at low temperatures. Appl. Catal. B Environ. 51, 93–106 (2004).

Article CAS Google Scholar

Machida, M., Uto, M., Kurogi, D. & Kijima, T. MnOx−CeO2 binary oxides for catalytic NOx sorption at low temperatures. Sorptive removal of NOx. Chem. Mater. 12, 3158–3164 (2000).

Article CAS Google Scholar

Liu, Z., Zhu, J., Li, J., Ma, L. & Woo, S. I. Novel Mn–Ce–Ti mixed-oxide catalyst for the selective catalytic reduction of NOx with NH3. ACS Appl. Mater. Interfaces 6, 14500–14508 (2014).

Article CAS PubMed Google Scholar

Eigenmann, F., Maciejewski, M. & Baiker, A. Selective reduction of NO by NH3 over manganese–cerium mixed oxides: relation between adsorption, redox and catalytic behavior. Appl. Catal. B Environ. 62, 311–318 (2006).

Article CAS Google Scholar

Wu, Z., Jin, R., Liu, Y. & Wang, H. Ceria modified MnOx/TiO2 as a superior catalyst for NO reduction with NH3 at low-temperature. Catal. Commun. 9, 2217–2220 (2008).

Article CAS Google Scholar

Xie, S. et al. Low temperature high activity of M (M = Ce, Fe, Co, Ni) doped M-Mn/TiO2 catalysts for NH3-SCR and in situ DRIFTS for investigating the reaction mechanism. Appl. Surf. Sci. 515, 146014 (2020).

Li, L. et al. Investigation of two-phase intergrowth and coexistence in Mn–Ce–Ti–O catalysts for the selective catalytic reduction of NO with NH3: structure–activity relationship and reaction mechanism. Ind. Eng. Chem. Res. 58, 849–862 (2019).

Article CAS Google Scholar

Wu, X., Si, Z., Li, G., Weng, D. & Ma, Z. Effects of cerium and vanadium on the activity and selectivity of MnOx-TiO2 catalyst for low-temperature NH3-SCR. J. Rare Earths 29, 64–68 (2011).

Article CAS Google Scholar

Niu, Y. et al. Synergistic removal of NO and N2O in low-temperature SCR process with MnOx/Ti based catalyst doped with Ce and V. Fuel 185, 316–322 (2016).

Article CAS Google Scholar

Wang, Q. et al. Effect of ceria doping on catalytic activity and SO2 resistance of MnOx /TiO2 catalysts for selective catalytic reduction of NO with NH3 at low temperature. Aerosol Air Qual. Res. https://doi.org/10.4209/aaqr.2019.10.0546 (2020).

Nalbandian, L. et al. Hydrothermally prepared nanocrystalline Mn–Zn ferrites: synthesis and characterization. Microporous Mesoporous Mater. 114, 465–473 (2008).

Article CAS Google Scholar

Thommes, M. et al. Physisorption of gases, with special reference to the evaluation of surface area and pore size distribution (IUPAC Technical Report). Pure Appl. Chem. 87, 1051–1069 (2015).

Article CAS Google Scholar

Xu, W., Yu, Y., Zhang, C. & He, H. Selective catalytic reduction of NO by NH3 over a Ce/TiO2 catalyst. Catal. Commun. 9, 1453–1457 (2008).

Article CAS Google Scholar

Qi, K. et al. Facile large-scale synthesis of CeMn composites by redox-precipitation and its superior low-temperature performance for NO removal. Powder Technol. 338, 774–782 (2018).

Article CAS Google Scholar

Lee, S. M., Park, K. H. & Hong, S. C. MnOx/CeO2–TiO2 mixed oxide catalysts for the selective catalytic reduction of NO with NH3 at low temperature. Chem. Eng. J. 195-196, 323–331 (2012).

Article CAS Google Scholar

Arena, F., Torre, T., Raimondo, C. & Parmaliana, A. Structure and redox properties of bulk and supported manganese oxide catalysts. Phys. Chem. Chem. Phys. 3, 1911–1917 (2001).

Article CAS Google Scholar

Wu, X., Liang, Q., Weng, D., Fan, J. & Ran, R. Synthesis of CeO2–MnOx mixed oxides and catalytic performance under oxygen-rich condition. Catal. Today 126, 430–435 (2007).

Article CAS Google Scholar

Giordano, F., Trovarelli, A., de Leitenburg, C. & Giona, M. A model for the temperature-programmed reduction of low and high surface area Ceria. J. Catal. 193, 273–282 (2000).

Article CAS Google Scholar

Watanabe, S., Ma, X. & Song, C. Characterization of structural and surface properties of nanocrystalline TiO2−CeO2 Mixed Oxides by XRD, XPS, TPR, and TPD. J. Phys. Chem. C. 113, 14249–14257 (2009).

Article CAS Google Scholar

Yao, H. & Yao, Y. Y. Ceria in automotive exhaust catalysts: I. Oxygen storage. J. Catal. 86, 254–265 (1984).

Article CAS Google Scholar

Chen, J. et al. A facile strategy of enhancing interaction between cerium and manganese oxides for catalytic removal of gaseous organic contaminants. Appl. Catal. B Environ. 250, 396–407 (2019).

Article CAS Google Scholar

Biesinger, M. C. et al. Resolving surface chemical states in XPS analysis of first row transition metals, oxides and hydroxides: Cr, Mn, Fe, Co and Ni. Appl. Surf. Sci. 257, 2717–2730 (2011).

Article ADS CAS Google Scholar

Leng, X. et al. Excellent low temperature NH3-SCR activity over MnaCe0.3TiOx (a = 0.1–0.3) oxides: influence of Mn addition. Fuel Process. Technol. 181, 33–43 (2018).

Article CAS Google Scholar

Andreoli, S., Deorsola, F. A. & Pirone, R. MnOx-CeO2 catalysts synthesized by solution combustion synthesis for the low-temperature NH3-SCR. Catal. Today 253, 199–206 (2015).

Article CAS Google Scholar

de Groot, F., Vankó, G. & Glatzel, P. The 1s x-ray absorption pre-edge structures in transition metal oxides. J. Phys.: Condens. Matter 21, 104207 (2009).

ADS Google Scholar

Cabaret, D., Bordage, A., Juhin, A., Arfaoui, M. & Gaudry, E. First-principles calculations of X-ray absorption spectra at the K-edge of 3d transition metals: an electronic structure analysis of the pre-edge. Phys. Chem. Chem. Phys. 12, 5619–5633 (2010).

Article CAS PubMed Google Scholar

Liu, C., Shi, J.-W., Gao, C. & Niu, C. Manganese oxide-based catalysts for low-temperature selective catalytic reduction of NOx with NH3: a review. Appl. Catal. A: Gen. 522, 54–69 (2016).

Article CAS Google Scholar

Marbán, G., Valdés-Solı́s, T. & Fuertes, A. B. Mechanism of low-temperature selective catalytic reduction of NO with NH3 over carbon-supported Mn3O4: role of surface NH3 species: SCR mechanism. J. Catal. 226, 138–155 (2004).

Article CAS Google Scholar

Kapteijn, F., Singoredjo, L., Andreini, A. & Moulijn, J. Activity and selectivity of pure manganese oxides in the selective catalytic reduction of nitric oxide with ammonia. Appl. Catal. B Environ. 3, 173–189 (1994).

Article CAS Google Scholar

Qu, W. et al. Single-atom catalysts reveal the dinuclear characteristic of active sites in NO selective reduction with NH3. Nat. Commun. 11, 1532 (2020).

Article ADS CAS PubMed PubMed Central Google Scholar

Yang, S. et al. Mechanism of N2O formation during the low-temperature selective catalytic reduction of NO with NH3 over Mn–Fe spinel. Environ. Sci. Technol. 48, 10354–10362 (2014).

Article ADS CAS PubMed Google Scholar

Download references

The authors thank the financial support from by Umicore N.V. The research was supported by the resources and facilities provided by King Abdullah University of Science and Technology. Polina Lavrik is also acknowledged for her support in the electron microscopy measurements. The authors also acknowledge the KAUST Imaging and Characterization Core Lab. We thank Sandra Ramirez-Cherbuy for the scientific illustrations of catalysts.

King Abdullah University of Science and Technology, KAUST Catalysis Center, Catalysis Nanomaterials and Spectroscopy (CNS), Thuwal, 23955, Saudi Arabia

Lieven E. Gevers, Linga R. Enakonda, Ameen Shahid, Samy Ould-Chikh, Cristina I. Q. Silva, Pasi P. Paalanen & Javier Ruiz-Martínez

Institut de Chimie Moléculaire de Grenoble, UAR2607 CNRS Université Grenoble Alpes, F-38000, Grenoble, France

Antonio Aguilar-Tapia & Jean-Louis Hazemann

Institut Néel, UPR 2940 CNRS, F-38042, Grenoble cedex 9, Grenoble, France

Jean-Louis Hazemann

King Abdullah University of Science and Technology, KAUST Core Labs, Thuwal, 23955, Saudi Arabia

Mohamed Nejib Hedhili

Umicore AG & Co. KG, Rodenbachen Chaussee 4, 63457, Hanau-Wolfgang, Germany

Fei Wen

You can also search for this author in PubMed Google Scholar

L.E.G. and J.R.M. conceived, coordinated the research, designed the experiments, and analyzed the data. L.R.E. and A.S. synthesized the catalyst materials and characterized them by TPD and BET. L.R.E. and A.S. performed the catalytic activity measurements. S.O.-C. performed and analyzed the electron microscopy and XAS measurements with the assistance of A.A.-T. and J-L.H. A.S., and M.N.H. performed and analyzed the XPS measurements. L.R.E., A.S. performed the XRD measurements and P.P.P. conducted the analysis. C.I.Q.S. performed the Raman and NO and NO+O2 experiments and analysis. J.R.-M. wrote the manuscript with the assistance of L.E.G., A.S., L.R.E., and F.W. All authors discussed the results and commented on the manuscript.

Correspondence to Javier Ruiz-Martínez.

The authors declare no competing interests.

Nature Communications thanks the anonymous reviewers for their contribution to the peer review of this work. Peer reviewer reports are available.

Publisher's note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and Permissions

Gevers, L.E., Enakonda, L.R., Shahid, A. et al. Unraveling the structure and role of Mn and Ce for NOx reduction in application-relevant catalysts. Nat Commun 13, 2960 (2022). https://doi.org/10.1038/s41467-022-30679-9

Download citation

Received: 27 October 2021

Accepted: 11 May 2022

Published: 26 May 2022

DOI: https://doi.org/10.1038/s41467-022-30679-9

Anyone you share the following link with will be able to read this content:

Sorry, a shareable link is not currently available for this article.

Provided by the Springer Nature SharedIt content-sharing initiative

By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.

What is SCR? Diesel selective catalytic reduction systems explained

What Is DEF?

News

Unraveling the structure and role of Mn and Ce for NOx reduction in application